THERE ARE A NUMBER OF STEPS INVOLVED IN MAKING YOUR OWN MODEM SETUP FILES. 
THE <MODEM>.MTC FILES ARE STORED IN THE INSTALLDRIVE>:\SYSCTX\TERM 
SUBDIRECTORY. THEY ARE FLAT ASCII TEXT FILES THAT HAVE THE FOLLOWING 
FORMAT: 

	/NAME:<TEXT DESCRIPTION OF MODEM>
	/CONN:<CONNECTION TYPE BIT MAP> (SEE BELOW)
	/FLOW:<FLOW CONTROL TYPE BITMAP> (SEE BELOW)
	/PAR:<PARITY, 0 OR 1>
	/BAUD:<BAUD RATE THAT MODEM TALKS TO COMPUTER>
	/STOP:<NUMBER OF STOP BITS, 0 1 OR 2>
	/DATA:<NUMBER OF DATA BITS>
	/INITSTR:<MODEM INITITIALIZATION STRING> (SEE BELOW)
	/HANGUPSTR:<STRING TO HANGUP MODEM>

/NAME: ENTER A DESCRIPTIVE TITLE FOR THE MODEM THIS WILL APPEAR IN THE 
SELECTIONS IN CONFIG TERMINALS SCREENS.

/CONN: NUMBER THAT IS GENERATED BASED ON THE CONNECT TYPE THAT IS SET UP. 
THIS  NUMBER IS FROM A BIT MAP AS FOLLOWS.

	CONNECT ON CTS IS 16
	CONNECT ON DSR IS 32
	CONNECT ON RING INDICATOR IS 64
	CONNECT ON DCD IS 128
	CONNECT ON FIRST CHARACTER IS 256
	DISCONNECT ON BREAK IS 4096
	CONNECT ON AUTO BAUD IS 512

YOU ADD UP THE NUMBERS AND PUT THE RESULT IN THIS FIELD. THIS WILL BE AN 
ITEGER NUMBER THAT WILL CREATE AN EFFECTIVE BIT MAP TO BE USED IN THIS FIELD.

/FLOW: NUMBER THAT IS GENERATED BASED ON THE FLOW CONTROL ITEMS THAT ARE 
SELECTED

	XON/XOFF TRANSMIT ENABLE IS 256
	XON/XOFF FULL DUPLEX IS 8192
	RTS/CTS ENABLE IS 16384
	RTS INPUT HANDSHAKING IS 32768
	DTR/DSR ENABLE IS 1
	DTR INPUT HANDSHAKING IS 2
	CTS OUTPUT HANDSHAKING IS 8
	DSR OUTPUT HANDSHAKING IS 16
	DCD OUTPUT HANDSHAKING IS 32
	DSR INPUT SENSITIVITY IS 64

THIS IS ANOTHER BIT MAP. JUST ADD UP THE NUMBERS AND PUT THEM IN THIS FIELD. 
YOU CAN CHECK YOUR WORK ONCE YOU CONFIGURE A TERMINAL BY SEEING IF THE 
CONTROLS IN CONFIG T MATCH THE BIT MAP YOU HAVE SET UP HERE.

/INITSTR: NEEDS TO HAVE YOUR MODEM SPECIFIC COMMANDS IT WILL START WITH "AT" 
THE ATTENTION COMMAND. YOU WILL HAVE TO CREATE THE REST OF THE STRING USING 
SOME OR ALL OF THE BELOW LISTED PARAMETERS DECODING THEM TO YOUR SPECIFIC 
MODEM.

ECHO COMMMANDS <E1>

AUTO ANSWER ON ONE RING <S0=1>

SET TO HIGHESTLEVEL OF DATA REL. COMM <%C, OR &K3 OR //N1 ETC> SET TO 
HIGHEST COMPRESSION RATE <MODEM DEPENDENT>

SET TO HIGHEST ERROR CORRECTION RATE <MODEM DEPENDENT>

SET TO DCD CONNECT, OR IF MODEM DOESN'T SUPPORT DCD SET FOR DSR TO TRACK DCD

TURN HARDWARE FLOW CONTROL ON <MODEM DEPENDENT>

TURN SOFTWARE FLOW CONTROL OFF <SET MODEM TO PASS XON/XOFF>

SET MODEM TO THE HIGHEST BAUD RATE <MODEM DEPENDENT>

SET LINE SPEED TO FLOAT <SO MODEM CAN LINK TO SLOWER SPEEDS>
	HI SPEED BAUD RATES MIGHT BE <$MB38400 OR $MB ETC> 

/HANGUPSTR:<COMMAND TO HANG UP MODEM> <~~~+++ATH0^M>

THE SIMPLEST WAY TO CREATE THIS FILE IS ACTUALLY TO START WITH AN EXISTING 
FILE AND MODIFY IT. THE MTC FILES ARE STORED IN THE <DRIVE>:\SYSCTX\TERM 
SUBDIRECTORY. COPY A SIMILAR MODEM TO A NEW FILE WITH A NAME THAT IDENTIFIES 
YOUR NEW MODEM AND AN EXTENSION OF .MTC.

EDIT THIS FILE ONLY ON THE FIRST LINE TO CHANGE THE MODEM NAME TO MATCH YOUR 
MODEM, THEN SAVE AND EXIT THE FILE.

NOW GO INTO CONFIG TERMINALS AND CREATE A NEW TERMINAL PROFILE USING YOUR NEW 
MODEM MTC FILE. YOU CAN NOW WORK WITH THIS TERMINAL CHANGING ALL OF THE 
PARAMETERS, SETUP STRINGS AND HANG UP STRINGS AND FLOW AND CONNECT 
INFROMATION UNTIL THE MODEM IS RESPONDING CORERECTLY AND RELIABLY. YOU WILL 
BE SAVING THIS  TERMINAL CONFIGURATION EVERY TIME YOU PRESS F2 WHILE YOU ARE 
DOING YOUR DEVELOPMENT WORK. IT IS SAVED IN THE <DRIVE>:SYSCTX\TERM 
SUBDIRECTORY UNDER THE NAME OF THE TERMINAL PROFILE. (UNDER HPFS IT WILL 
HAVE A LONG NAME PREFACED BY TC.) YOU CAN PRINT OUT THE TERMINAL PROFILE AND 
MANUALLY ENTER THE APPROPRIATE VALUES INTO THE MASTER NEW MTC FILE FOR THIS 
MODEM THAT YOU PREVIOUSLY CREATED. ( COPY THE FLOW VALUE, CONNECT VALUE, INIT 
STRING, HANGUP STRING) YOU CAN THEN CREATE ANOTHER TERMINAL( NEW NAME SO YOU 
DON'T DESTROY YOUR WORKING TERMINAL) AND TEST IT FOR OPERATION. IF IT WORKS 
CORRECTLY YOU ARE DONE, IF NOT YOU SHOULD COMPARE THIS TERMINAL TO THE 
WORKING TERMINAL FILE AND NOTE AND CORRECT THE DISCREPANCIES. THIS IS NOT AN 
EASY PROCEDURE BUT IT IS POSSIBLE FOR YOU TO CREATE YOUR OWN. WE WILL WORK TO 
HELP YOU IF YOU HAVE PROBLEMS.

WE CONSTANLY UPDATE OUR LIST OF SUPPORTED MODEMS IN A FILE ON THE CITRIX BBS 
CALLED MODEMS.ZIP THE BBS NUMBER IS 305-346-9004. USE PROCOMM PLUS OR SIMILAR 
PROGRAM SET TO N81 AND GET THE LATEST FILE. 

NOTE: IF A COMMAND IN THE HOST INIT STRING REQUIRES A "\" CHARACTER YOU NEED 
TO HAVE TWO IN A ROW. THIS WILL BE FIXED TO ONE IN A FUTURE RELEASE.